hide camera auto pictured to your GSM mobiphone when alarm happened at your home or office ,inside camera with a high-resolution(10,0000) color picture
Where to used?
1. Car alarm.
2. Home or office alarm.
3. Electronical appliances both at home and in the office.
4. Factory otomation systems.
5. TV, radio and GSM stations repairs.
6. Watering systems.
7. Water tanks.
8. And much more...
--------------
Is the system CE-approved ?---------yes,GSM model
Does it work also on 433 MHz between sensor and main-unit ?--------315MHz ;433 MHz
Is the latest product with inside camera ?--------------------yes.
Do you have some manual or is it the manual on the website ?-----------------yes,we have
Is it possible to send a request to the camera and get a picture back ?-------yes
Is the picture sent as a MMS-message ?-------------------------right
black box(inside battery supply)：
FOB prices(forminimum order quantity) 197 usd(1 base$175+ 2 controller$6 +1 magnetic $6 + 1infrared$10 )
Minimum order quantity 100 set
Sample availability/cost 350 USD(With DHL)
Add:
Wireless magnetic detector ------- 6 USD,
Inactive infrared intruding detector ---10 USD,
Cordless remote controller -----3 USD,
Cordless smoke detector ------ 25 USD,
Sound alarm outside-------------- 10 USD,
GSM-- camera
1,GSM-CAMERA alarming controller
2,inactive infrared intruding detector (up to 10)
3,wireless magnetic detector (up to 10)
4, cordless remote controller (two or more)
5, have 3 group dialing, voice alarm and live monitor
6, remote control and emergency alarm
7,moniter the voice in home when alarm
8, hide camera auto color pictured to your GSM mobiphone
9,inside Li battery can be used in a week without charger.
HOW WE ENTER THE PHONE NUMBERS TO DIAL?
The GSM system need SIM card to dial. So, you can use your own mob-phone to program it, you can set 3 phone number in SIM card, be sure in first (1,2,3) position in the SIM card, which 3 number is to be dial out when alarm is happen.
1). POWER ON
When you set the SIM card (have first 5 number) into the GSM base, turn power on, the lamp on panel will bright on green
You can set any one detector to the system when the GSM base start power on in 20 second. After 20 second, the system will not set any detector into the base.
-------You needn’t do below, for we have set all sample detectors into the base.
2). When you wand to set Wireless Infra Red Detector in the system, you can open the power of Wireless Infra Red Detector, the system will send out a whisper, the lamp on panel will flash on red. It is ok.
3). When you wand to set Wireless Magnetic door detector in the system, you make it work, the system will send out a whisper also. The lamp on panel will flash on red. It is ok too.
4). Two of the remote controller have set into the system, you don’t need to set again, but if you want to set, you can do as this: push the button (^) on the first remote controller, the system will send out a whisper, and push the button (^) on the second remote controller, the system will send out a whisper also. The lamp on panel will flash on red. These two remote controllers have set into the base.
5). When you end the system set, after 20 second, you can test the system
6). The remote controller has four buttons; button1, set alarm work；button2, set alarm off; button3, set emergency call；button4 (set into base). If you push button2 and button4 at same time,
You will hear: 3 ‘ Bi’ show alarm sound out is off; 1 ‘ Bi’ show alarm sound out is on
7). When you wand to exit all the detector in system, turn off the power, and push the key on panel (beside left, a small hole), then, put on the power, after 3 second, the lamp on panel will flash on red, it is ok.
HOW WE CONTROLL THE GEM-CAMERA BY OUTSIDE PHONE?
Pick up the phone and dial to the GSM-Camera, you will hear “ Bi “, then inter password 1 2 3 4 #, (1234 is first code in the base), you hear a short “ Bi “, this means you can hear the voice in the alarm place and you can operate the base:
A) dial 0 # ,alarm on(detector use)；dial 0 * ,alarm off(detector no-use)；A long “ Bi “ show operates successful.
B) dial 6 # ,take a picture and send to your mobiphone; dial 6 * no take a picture ,A long “ Bi “show operates successful.
---this fanction show that you can dial in to get a picture ,if you set 3 group mobiphone in the base, it will send the picture to all of them at sime time. Then,the base will take anther picture and send out, three time.
H) dial 7 # , set outside sound work 3 min when alarm happened；dial 7 * set outside sound disable when alarm happened ,A long “ Bi “ show operates successful.
---this fanction show when outside speaker can sound or not when alarm happened
I)Dial 8 # or 8 * a short “ Bi “ show you inter new password, you may dial 8 0 0 0 #. ；A long “ Bi “ show operates successful. That is change password from 1234 to 8000
J) Dial 9 #, set sound out on 3 min at once; dial 9 *, set sound out off at once; a long “ Bi “ show operate successful.
---this fanction show when you dial in and listen surround voice,if you find one in,you can set outside speaker alarm on 3 min .
Note:
A-- when every first time power on, the system will waiting for you to set any one detector, and the lamp on panel will bright on red. If you not do this again, please wait 30 second, the base auto inter into alarm state, the lamp on panel will flash on green. Then you can test it.
B-- when you have not set any phone number to the system, the lamp on panel will bright on yellow, when you have set mane and number to the system, the lamp on panel will flash on green.
C-- when alarm happen or you call in to monitor, the lamp on panel will flash on red.
D—you must connect the longer wire to ANT for controller antenna.
(A) About Phone number
1) can save 3 group phone into base
2) every group must set a name (not more than 3 bit),
3) every group phone number(not more than 16 digit),
(B) About LED
1)power on,LED show red in 30 sec.in this time,you can fit wireless detector into base,if do,the red flash.
2)If yellow LED flash show it start to get in touch GSM network .
3)If yellow LED still flash ,show SIM card is set un-correctly or GSM network is not good.
4)If yellow LED still on,show not name or phone number in SIM card .
5)if every thing is ok,LED show green flash(in alarm situation)or green on (no in alarm situation)
6) if alarm happened,LED show red and start dial out.
|
|
|
|
Product Image
|
