DVR-MMS Alarm with PIR & SD
1) 300K pixels digit camera 11) Alarm to 5 groups phone
2) PIR detector 12) Alarm to 1 group monitor center
3) Video motion detection 13) Alarm to 1 group SMS center
4) IR for night use 14)Alarm to fix IP address
5) Video untoQVGA (320×240) 15) Alarm to 2 groups Email
6) Ready time recording 16) Intervaltime to reporting
7) Support unto 16GB SD card 17)Fixed time of arm and disarm
8) Adjusted to QCIF, CIF, VGA 18) Built-in four- bands GSM
9) Listen-in function 19) Built-in lithium battery
10)16 zone wireless detectors 20) with one wire input alarm
How to use it:
1) Open thebattery cover, put SIM cart in it,Inserts the SD card (FAT32) into the base (if you have it), put the power 5V/2A DC into the base, put down switch of the base to open power supply. The LED turns to red and last for 20, and it will start to search GSM network. After 20 seconds, the LED is flashing in orange and the alarm system begins to read the information of the SIM memory. It will enter into the status of disarm and LED is go still green. It will be turned to be green and flashing in the status of alarm when you use controller to set the base in alarm. The LED is red and flashing when the base is in alarming.2) You can send the message to setup the base .The format:
password #operation code # content #123456#11#1#; set the base alarm ; LED green and flashing in the base123456#31#99998888#1#1#0# , set phone 99998888 and sent out message and picture when alarm.123456#1#1#; get one picture by your mob phone if MMS setting is ok 123456#21# CMWAP# # #10.0.0.172#9201# http:/mms.monternet.com # Shush as MMS setting show in CHINA( other country will be different):Access Point Name(APN):CMWAP ;Set GPRS Access point.Username: (empty) ; Set MMS User name.Password: (empty) ; Set MMS User Password.Gateway IP (proxy) addresses (IP): 10.0.0.172 ; Set IP Address.Port: 9201 ; Set PortMMS (Relay) Server URL: http:/mms.monternet.com; Set MMS Homepage.
|
Com
|
Function
|
|
1#-#
|
1#(picture 1-20)#;ask picture by your mob phone; 1*, ‘ * ’ stand for approves
|
|
11#-#
|
11#1# (Arm) ;11#0# (Disarm)*; set the base alarm or disclaim
|
|
12#-#
|
12#(arm time 0000-2359)#(disarm time 0000-2359)# ; set arm time-gap or disarm time-gap
|
|
14#-#
|
14#( picture 1-20)# ; sent picture to your mob phone when alarm ,1*
|
|
15#-#
|
15#1#; PIR work*; 15#0# ;PIR no work; set PIR detector work or no work
|
|
16#-#
|
Set the sensitivity of camera(1—99); 0 -- close;1 -- high sensitivity and 99 is low sensitivity, 15 *
|
|
17#-#
|
17#( 0-2)# ; Set picture size: 0 --160x128; 1*-- 320x240; 2 -- 640x480
|
|
18#-#
|
Change password (1—6 bit). 18#(1-6)#; 123456*
|
|
19#-#
|
19#1# ;Set CHINESE version * ; 19#0#; Set ENGLISH version
|
|
20##
|
Show MMS setup in the base; 20##
|
|
21#-#
|
MMS setting : 21# APN# USER# PASS# IP# PORT# MMS Homepage#
|
|
30##
|
show preset phone number and status in the base; 30##
|
|
(31-35)#-#
|
(31-35)# phone number # SMS (0,1)#MMS(0,1)# phone(0,1)#; 0--disable; 1--able 32#99997777#1#0#1# ,show sent message and call out 99997777 when alarm.
|
|
40#-#
|
Show Email address in the base 40##
|
|
41#-#
|
Set First Email address(0—31bit) ; 41#269999@163.com#
|
|
42#-#
|
Set Second Email address(0—31bit)
|
|
50#-#
|
Show monitoring center phone number. 50##
|
|
51#-#
|
51# (center phone )#( user ID)# (arm or disarm report)# (1-- report；0-- no report )
|
|
52#-#
|
arm or disarm report center numbers: 52# arm report number# disarm report number #
|
|
53#-#
|
Set NetWare IP Address 53#( IP)# (PORT)# (user ID)#
|
|
54#-#
|
Set SMS center number. 54# (mob phone number) # (user ID)#
|
|
55#-#
|
Set time interval reporting :55# (center number 0-15bit)#( Time interval 1-99hour)# (Type 0-2)# Type: 0---send SMS;1---send MMS;2--- send SMS + MMS
|
|
70#-#
|
Show wireless detector status (1-16)： 70# (1-16)#
|
|
(71-86)#-#
|
(71-86)#( 1-2 )# (SMS-24 bit)# ; (0--disarm,1--arm,2--24hours arm) 71#1# front door PIR alarm# ; show first detector can arm and send message (front door PIR alarm)
|
|
100##
|
Set real time
|
How to add more detectors?
You can add new detector, such as wireless door sensors, PIR Sensors, gas and smoke detectors when you push the reset key (inside the battery cover) until the LED change from green to red. You should trigger every detector, and the red LED will flash and shows successful .After you finish doing it, you can push the reset key again or waiting 20 seconds, it ends and automatically enter into working state.(with green LED),you can program it by 71# --86#
How to cancel the lost detector?
It often happens that some of coded detectors are lost. You can cancel the coded information of this detector so that it can not control your alarm system. Just reset the alarm system by keeping reset key and turn on power and then beep or LED flashes, it shows reset is successful. All registered detector have been deleted and password is123456. You can register them again with the above solution.
How to control the base with remote controllers?
When you press, “alarm”, the LED of the base will be turned green with flashing. It shows the base is in arming status, it will alarm and dial out when you remove the door sensor, switch PIR Sensor, go across from the front of camera and so on. The LED will turn to red with flashing when the base is alarm. When you press, “disclaim”, the LED of the base will turn green and does not flash. It won’t alarm and dial out. When you press “Emergency help”, it will alarm and send MMS and SMS or dial out no matter it is under arming status or disarming status. The LED will be red with flashing. .
